Mold Solutions by Cowleys Before & After Photos

Before this family could sell their home in Asbury Park, NJ, they first needed to address the massive mold growth in their attic. The conducive condition that caused the mold growth was the lack of ventilation in the attic. Although the homeowners installed several new attic fans, it was too late and mold had grown on every square inch in the attic. So the homeowners called our office to get rid of the mold.

After equipping our personal protective equipment (PPE) we treated the mold directly with an antimicrobial solution called Mold Abatement Polymer Solutions 1 (or MAPS 1 for short). MAPS 1 is an EPA registered product that attacks mold at its DNA and kills it immediately. After treating the entire attic with MAPS 1, we used our mold stain remover and began scrubbing away all the mold growth throughout the attic.

Now that the mold has been killed and all the stains are removed, we then applied our patented sealant called MAPS 2. MAPS 2 is a moisture-sensitive application that encapsulates the surface mold is growing on and renders it harmless, inert, and non-allergenic. One of the best features of MAPS 2 is that it will reactivate whenever it gets wet to prevent future mold growth, meaning that there will be no more mold growth in the attic for the current and future homeowners!

These homeowners in Belmar, NJ recently had their roof replaced because of roof leaks. During the renovation, they found mold growth in the attic from water intrusion. Fortunately, the roof replacement fixed the underlying water intrusion problem, but there was still dangerous mold growth that needed to be removed. 

As is often the case, there were no water-damaged building materials, so there was no need for any massive tear-out and renovation. Instead, we could efficiently and effectively chemically treat and kill the mold in less than a day, saving thousands of dollars on unnecessary construction. We first treated the affected areas by applying our EPA-registered anti-microbial product called MAPS 1. This application attacks mold on a cellular level and kills it instantly.

We then scrubbed away the mold and applied MAPS 2, which is our patented sealant that encapsulates the surface mold is growing on and renders the mold non-allergenic and harmless. MAPS 2 is also moisture-sensitive and reactivates whenever it gets wet to prevent the return of mold.

With the help of Mold Solutions by Cowleys, these homeowners did what makes the most sense when it comes to mold removal — treating the mold right where it sits and leaving perfectly good building materials alone. By doing so, the homeowners expediently and effectively got rid of the mold, and one less potential headache was resolved. 

Recently, during a pending sale of a home in Wall Township, NJ, the home inspector found mold growing underneath the basement stairs. At some point, there had been a small water intrusion in that corner of the basement, and, unbeknownst to the homeowner/seller, had triggered some mold growth. The mold growth wasn’t extensive, which is probably why it went unnoticed until discovered by the home inspector. Nevertheless, it was enough of a problem to potentially throw a wrench into the works, so to speak, so the homeowner contacted Mold Solutions by Cowleys to treat the mold. 

After identifying the mold-affected areas of the basement, we applied an EPA-registered antimicrobial MAPS 1, which attacks mold at its DNA and kills it instantly. Next, we applied MAPS 2, which is our patented sealant that encapsulates the surface mold is growing on and renders the mold non-allergenic and harmless. MAPS 2 is also moisture-sensitive and reactivates whenever it gets wet to prevent the return of mold. Some staining had occurred on the walls, but they are purely aesthetic and pose no health risk. Once MAPS 1 & 2 have been applied, the mold is no longer a threat.

A homeowner inspection that uncovers mold growth does not necessarily mean a lost sale or significant renovation expenditures to remedy the problem. Instead, with our mold treatment process, we can resolve most mold issues in less than a day — and with a pending sale that means no delay in the closing.

Recently, I went on a service call to a commercial property in Wall NJ, after the property owner found mold during his renovations. Before beginning my inspection, I equipped my personal protective equipment (PPE). Why? Once mole spores are disturbed, the spores detach and start floating everywhere, landing on anything and anyone. If you’re not wearing any PPE, you’re inviting all of those mold spores to settle on your clothing, the area you’re cleaning, your shoes (allowing mold to travel to other areas in your home), in your eyes, and up your nose into your upper respiratory system! This is an imperative first step to any mold inspection.  

Once I put on my PPE I began my inspection of the entire property. After a thorough inspection, I noticed a small amount of mold growth on the interior of the wall plywood. As I took a closer look, I noticed there was moisture entering from the exterior siding. Turns out the siding of the building is stucco and water was flowing from the top of the building between the stucco and the sheathing. This moisture led to mold growth. Mold thrives on organic materials like natural fibers (cotton, wool), paper, leather, wood, or surfaces coated with organic matter such as food, grease, and soil. Mold grows best in warm temperatures of 77 to 86 degrees and needs moisture that can come from water leaks, flooding, high relative humidity, or condensation. Mold growing on exterior stucco walls is not only unsightly, but it can also cause larger problems if it gets in between your home's exterior stucco and framing. 

Before treating any mold on your property, you must first fix the problem or the water source causing the mold to grow. Fortunately, the property owner repaired the leak by the time I arrived. 

In order to begin the treatment process successfully, I needed to remove the insulation in the affected areas to gain access to the sheathing. The property owner allowed me to do so as the contractor he hired will replace the insulation and drywall. Then, I applied an EPA-registered, non-toxic antimicrobial solution called Mold Abatement Polymer Solutions 1 (MAPS 1). MAPS 1 breaks down mold at a cellular level and kills it instantly. Once that solution dried, we applied a patented sealant called MAPS 2. This moisture-sensitive sealant encapsulates mold, rendering it inert, harmless, and non-allergenic. MAPS 2 reactivates when it gets moist to prevent the growth of any future mold colonies. Now the property owner can continue his renovations in a safe, mold-free environment.  

Recently, the Cowleys Mold Solutions Team went on a service call to a residence in Belmar, NJ. The homeowner contacted us because of mold growth in his living room. 

Mold is an unwanted by-product of a water or moisture problem in a building. There is a long list of possible water intrusion events that goes well beyond flooding. Mold can form because of leaking pipes, dampness and humidity, especially in basements and crawl spaces, and rain seeping in because of damage to the roof, surrounding fascia boards, and around window frames. For many, exposure to mold can be harmful, leading to long-term chronic health problems, especially for those with pre-existing respiratory conditions and other risk factors.

As we were putting on our personal protective equipment (mold is a serious biohazard in enclosed spaces) we asked the homeowner if he knew of any water intrusion on his property, such as a recently burst water pipe. This preliminary information helps us determine the underlying cause of the mold growth. We don’t just want to treat the current mold. We also want to fix the underlying problem so that mold doesn’t return. The homeowner informed us that a pipe did, in fact, burst in his living room while he was away at work. Fortunately, his son happened to come home early from work and was able to stop the water leak. Otherwise, the problem would have been much worse.

As we began our inspection in the living room, we immediately noticed mold growth around a particular window frame. Unfortunately, after a more detailed inspection, we found that the mold and water damage was more extensive than we first thought. Some of the drywall was so damaged that it had to be removed. If building materials have not lost their structural integrity, we can often just treat the mold. However, sometimes the water damage is too much. Here, we needed to remove some of the drywall, and we started to cut the drywall in those areas where the moisture and mold were most visible. Once the window trim was removed, we could see there was mold growth between the trim and the drywall that wrapped around most of the window. We kept cutting and removing the damaged building materials until we reached the undamaged areas of the drywall. 

After the damaged drywall was removed, we applied MAPS 1(Mold Abatement Polymer Solution 1), an EPA-registered anti-microbial. This application is specifically designed to kill active mold growth. We then scrubbed away the surface mold and applied MAPS 2, a patented polymer sealant that encapsulates the existing dead mold and prevents future mold from growing.

After we were finished with our treatment, the homeowner informed us that he scheduled an appointment with a contractor to install new drywall in the living room. Although no one likes these unexpected events, the homeowner was relieved that the dangerous mold growth was removed from his home and he could now move forward with the necessary repairs without worrying about any hidden mold.